COMBIFLEX SIKA PDF

The Sikadur®– Combiflex® SG System is a high performance joint sealing system for construction, expansion and connection joints as well as for cracks. Sika® ‘White Tank’ System and refurbishment with the. Sika® -1 Prebagged System. Sikadur® Combiflex® tested under high water-pressure. In conjuction with. The Sikadur®-Combiflex® SG System consists of a flexible Polyolefin (FPO) . Sika® System test: Sikadur®-Combiflex® SG Tapes bonded to each other with.

Author: Gardazuru Feran
Country: Swaziland
Language: English (Spanish)
Genre: Music
Published (Last): 16 June 2008
Pages: 302
PDF File Size: 20.45 Mb
ePub File Size: 12.23 Mb
ISBN: 525-6-89380-544-9
Downloads: 67089
Price: Free* [*Free Regsitration Required]
Uploader: Tegal

During this operation, take care to ensure that the epoxy adhesive does not enter the joint. Do not expose vapours to naked flames or sparks. Only mix sufficient material that can be readily used within its pot life.

SIKA >4 Inch Combiflex – Joint Tape, Usage: Sealing, Rs /roll | ID:

Colma Cleaner and Hypalon Welding Solvent. These two products combine to form commbiflex highly flexible, waterproof, surface bonded bandage. Typical application areas for 2 these highly resistant products are: In damp conditions use a chalk mark.

Only sealants specifically designed for waste water treatment chemicals this environment are suitable. On the other hand, joints in pedestrian areas should be flush with the The optimal ratio of joint width to depth seal- surface to prevent injury of people.

Remove all loose materials, such as cement laitance and dirt, mechanically, with a wire brush, or by water or sand blasting.

Waterproofing Tape System for Cracks and Joints with Sikadur Combiflex® SG

Wash hands immediately after use. To start renovating the joint pick or cut out the old or damaged sealant using, for exam- 1 2 ple, an oscillating knife or similar tools. All of them exhibit a long service life even un- der permanent water immersion and resist aggressive liquids used in water treatment plants.

  EC2203 SYLLABUS PDF

Without tooling a smooth surface airplanes, maintenance vehicles and trucks is achieved. Activated sheeting must be used within 8 hours. The product is substrate surface must be clean, dry and free used to activate non-porous substrates such from any grease, oil, dust, release agents and as metals, plastics, glazed ceramics and various any other substances that potentially could have painted surfaces.

Hypalon Welding Solvent should be liberally applied to both sides of the lap. The surface may be dry or damp, but it must be free of any standing water. Laps or welds must be a minimum of 50 mm wide and they can ccombiflex achieved by hot air welding using Hypalon Welding Solvent. Sikadur 31 can either be mixed by hand in small quantities, i.

In this brochure Sika solutions and concepts for floor and pavement joint sealing as well as other special applications are de- scribed in detail. Use cover plates over joints in traffic areas.

SIKA SIKADUR® COMBIFLEX SG SYSTEM

Depending upon the on-site conditions, all lapping and welding of the Combiflex Hypalon Sheeting should be completed before installation. See Packaging below for roll dimensions.

Ensure that it is worked well into the surface, especially if the surface is damp. Drinking water is one of the most important resources that needs protection.

  ALTERA MAX 3000A CPLD PDF

Log In Sign Up. In order for a sealant to fulfil its function over the whole lifetime of a building or construction the selection of the right solution and the cor- rect design taking into account all potential influences are essential. An old sealant needs to be renovated at the sealant with similar dimensions as the original end of a normal life cycle or because of main- joint or a sealant with similar mechanical Reasons for joint refurbishment may include tenance or quality insufficiency reasons.

Otherwise there is an increased risk of accidents. This sig- floor stays tight even under heavy loads. Apply a 1 mm thick, 40 mm wide minimum layer of Sikadur 31 to the prepared substrate by trowel, spatula or a stiff brush between the masking tape or chalk mark and the joint on either side of the joint as shown in Diagram 4.

Contact Sika for further health and safety information. Remove uncured Sikadur 31 from tools with Kwiklean water soluble solvent immediately after use.

Sikadur®- Combiflex® SG System | Sika Waterproofing

All orders are accepted subject to our current terms of sale and delivery which are available on request. The resistance of the sealant ensures in case of an accident the tightness of the con- combiflsx bund for a longer time then usual sealants would do.

The than common floor joint sealants.